Free tool

Stockpile volume calculator.

Work out the volume and weight of a pile from a few tape-measure numbers. Pick the shape, type the sizes, and the answer updates as you type. The sums run in your browser and nothing is sent anywhere.

Free, no sign-up Cone, flat-top, long and rectangular piles Metric or imperial
Calculator

Pick the shape, type the sizes.

Units
Pile shape
h D
Side view. D is the widest distance across the base.
I know the

The widest distance across the bottom of the pile.

Walk or tape all the way round the foot of the pile.

The widest distance across the bottom.

Across the flat top. It cannot be wider than the base.

The full length of the pile including the rounded ends.

The widest distance across the foot of the pile. The length cannot be shorter than this.

The long side of the foot of the pile.

The short side of the foot of the pile.

The long side of the flat top. It must fit inside the base.

The short side of the flat top. It must fit inside the base.

Straight up from the ground to the top of the pile.

Typical loose bulk densities, they vary with moisture and grading. Use your own figure if you have one.

Result

Fill in the sizes and the volume appears here.

These are sums on an ideal shape: a quick estimate, not a survey. See below for why.

The formulas

Four shapes, four formulas.

Each one is the volume of a solid you can picture, worked in metres and converted at the end. h is always the height straight up from the ground to the top.

CONE

Heap tipped from a point

V = π × r² × h ÷ 3

r is the radius of the base, which is half the diameter. If you only know the distance around the base, r is that distance divided by 2π.

FLAT-TOP ROUND

Truncated cone

V = π × h × (R² + R × r + r²) ÷ 3

R is the radius of the base and r the radius of the flat top. The top cannot be wider than the base. With r = 0 it becomes the cone.

LONG PILE

Windrow with rounded ends

V = W × h × (L - W) ÷ 2 + π × (W ÷ 2)² × h ÷ 3

A triangular ridge of length L - W, plus a cone made of the two rounded ends. L is the full length and W the width across the base, so L cannot be shorter than W.

FLAT-TOP RECTANGULAR

Prismoid

V = h × (A1 + A2 + 4 × Am) ÷ 6

A1 = L1 × W1 is the base, A2 = L2 × W2 is the top, and Am = ((L1 + L2) ÷ 2) × ((W1 + W2) ÷ 2) is the middle. The top must fit inside the base.

From volume to weight

Weight is volume times the bulk density of the material as it lies in the pile.

weight = volume × density
  • 1 ft = 0.3048 m
  • 1 m³ = 1.307951 yd³ = 35.3147 ft³
  • 1 tonne = 1.102311 US short tons
  • 1 t/m³ = 0.842778 short tons/yd³
A worked example

A cone, 20 m across and 6 m high.

r = 20 ÷ 2 = 10 m
V = π × 10² × 6 ÷ 3 = 200π = 628.3 m³
weight = 628.3 × 1.6 t/m³ = about 1,005 t

1.6 t/m³ is a typical figure for dry sand. In US units that pile is about 821.8 yd³ and 1,108 short tons.

The honest part

Why a formula is only a starting point.

  • Real piles are not clean shapes. They slump, lean, get scooped from one side and sit at a different angle on every face. A cone formula on a lopsided pile is a rough guess at the shape.
  • The ground is rarely flat. The formulas assume a flat base at one level. A pile on a slope, or in a shallow hollow, has a base that is not where the formula thinks it is.
  • Dug faces and benches do not fit. A pile a loader has been cutting into has steep faces and steps, not the smooth sides these shapes assume.
  • Height is the awkward number. It goes straight into the answer, so a different height gives a different volume, and nobody should climb loose material or stand under a face to measure it. A tape, a guess by eye and a laser from the wrong spot all give different heights.
  • We do not put a percentage on how far off a formula can be. It depends on the pile, and a number we made up would be worse than none.
When the number has to hold up

Measure the real pile from drone photos.

A formula describes an ideal pile. A drone flight measures the one that is actually there. Helios rebuilds the pile from your photographs as a dense point cloud and a surface model, and the volume is taken on those. Nobody climbs the pile, and every flight stays as its own dated record, so next month is a comparison and not a fresh argument.

Scale is only tied to real-world units when ground control is used, and material the camera never saw is not reconstructed. The stockpile page spells out what that means for your flight.

Questions

Asked before you ask.

What is the formula for the volume of a stockpile?

It depends on the shape. A conical pile is V = π r² h / 3, where r is the radius of the base and h the height. A round pile with a flat top is a truncated cone: V = π h (R² + R r + r²) / 3. A long pile with rounded ends is a triangular ridge plus a cone at the ends: V = W h (L - W) / 2 + π (W/2)² h / 3. A flat-topped rectangular pile is a prismoid: V = h (A1 + A2 + 4 Am) / 6. The calculator on this page works all four.

How do I convert stockpile volume to tonnes?

Multiply the volume by the bulk density of the material: tonnes = cubic metres x tonnes per cubic metre. Use the loose bulk density of the material as it lies in the pile, not the density of solid rock. In US units, short tons = cubic yards x short tons per cubic yard, and 1 tonne per cubic metre is 0.842778 short tons per cubic yard. Density moves with moisture and grading, so a figure from your own material beats any table.

How do I measure the height of a stockpile safely?

Stay on the ground. Measure from level ground at a safe distance, to the side of any loose face, with a laser rangefinder or a clinometer, and never climb a loose pile or stand under an overhanging face to get a number. If you cannot get a safe height, a drone flight measures the pile without anyone on it.

How good is a stockpile volume formula estimate?

A formula is exact for the ideal shape and only as good as the match between that shape and the real pile. Real piles slump, lean, sit on uneven ground and have dug faces, so a formula gives a quick estimate and not a measurement you can defend to a third party. We do not put an error percentage on it, because it depends on the pile. When the number has to stand up, measure the pile itself.

Which pile shape should I pick?

Pick the one that looks most like the pile from the side. A heap tipped from a conveyor is usually a cone. A pile with a flat top is a truncated cone if it is round or a prismoid if it is rectangular. A long, ridged pile with rounded ends is a windrow. If the pile fits none of them closely, treat the answer as rough.

Next

Measure the real pile in a few minutes.

Create an account, upload the photographs and the fixed quote is on screen before anything runs. An account is free and needs no card.

Create an account Email us

[email protected] · Eyona Software Development (Pty) Ltd, Cape Town · Helios runs at portal.helios3d.co.za